High-quality full cheek crankshaft for Morini M0, M01 and M1 engines which is installed on Alpa Turbo / Chopper and Malaguti Fifty mopeds, among others.
The connecting rod is highly polished. In addition, the rear connecting rod bearing is a silver bearing, which has excellent emergency running properties. The balancing bores of the racing crankshaft are sealed with aluminum inserts for greater pre-compression.
Note: The crankshaft does not fit FMT1 CH engines.
Corresponding bearings, oil seals, racing cylinders etc. can be found in the accessories section.
Branded product from the Portuguese manufacturer Jasil under the Top Racing brand.
Details
Manufacturer | Jasil |
Area of application | Racing |
Cheek type | Full cheeks |
Crankshaft stroke | 39 mm |
Ø piston pin (B) | 12 mm |
Total length of crankpin on clutch side | 71 mm |
Total length crankpin ignition side | 67.25 mm |
Ø Bearing seat (clutch side) | 17 mm |
Ø Bearing seat (ignition side) | 17 mm |
Suitable for the following models
Alpa Chopper / Turbo | |
Malaguti |
Accessories & related products
Airsal 43.5 mm cylinder kit 12 mm KoBo | Morini
Nominal diameter: 43.5 mm · Manufacturer: Airsal · Material: Cast aluminum · Surface: sandblasted · Ø cylinder neck: 47.9 mm · Ø outlet inside: 23.2 mm · Area of application: Tuning · Number of fixing points: 4 pcs · Ø piston pin (B): 12 mm · Hole pattern [mm]: 46 x 46 · Outlet type: straight · Hole spacing outlet: 35 mm · Thread outlet: M5x0.8 (standard thread) · Decompressor: No · Camouflaged: No
111,70 EUR
Moped fans like you also bought:
Magura cable clamp Ø 8 x 15 mm
Total length: 15 mm · Thread length: 7 mm · Manufacturer: Magura · Material: Brass · Area of application: Standard · Material: Steel · Surface: blue galvanized · Surface: nickel-plated · Thread type: M6x1 (standard thread) · Ø Cable bushing: 2.3 mm · Drive: External hexagon · Drive: Slot · Ø Bundle: 6 mm · Screw head: Hexagon · Width across flats SW: 7 mm · Ø outside: 8 mm
2,80 EUR
swiing® revival snap ring low control bearing set (version 2.0)
Manufacturer: swiing® revival parts · Material: Spring steel · Surface: blank · Thickness: 0.6 mm · Height: 7 mm · Nominal diameter: 20 mm · Nominal diameter: 28 mm · Puch spare part no.: 349.1.30.015.1 · Sachs spare part no.: P0521
2,80 EUR
Magura adjusting screw brake long
Manufacturer: Magura · Material: Brass · Surface: nickel-plated · Color: silver · Drive: Knurled screw · Ø External head: 9.1 mm · Total length: 47 mm · Total length: 65 mm · Ø shaft: 6 mm · Shank length: 11 mm · Thread type: MF6x0.75 (fine pitch thread) · Thread length: 24 mm
4,35 EUR
NTN 6203 C3 Ball bearing 17/40/12
Material: Steel · Surface: blank · Bearing type: Deep groove ball bearing · Stock number: 6203 · Inner ring width: 12 mm · Manufacturer: NTN · Bearing clearance: C3 · Bearing cage: "-" Sheet steel cage ball-guided · Groove ring: No · Width: 12 mm · Ø outside: 40 mm · Ø inside: 17 mm · Area of application: Standard · Ball bearing closed: No
9,95 EUR
Oil level screw engine | Zündapp Bergsteiger / Alpa Chopper / Malaguti Fifty
Manufacturer: ALPA · Material: Steel · Surface: blue galvanized · Area of application: Standard · Thread type: M6x1 (standard thread) · Drive: Slot · Screw head: Cylinder head · Thread length: 16 mm · Color: silver · Number of components: 1 pcs
2,70 EUR