The Spark EVO Zero Basic module (version 2.0) was developed to make the breaker ignition on your Puch moped / moped significantly more wear-resistant and low-maintenance.
The box uses the breaker only as a clock generator and replaces the capacitor at the same time. Problems with worn breaker contacts and poor quality capacitors are therefore a thing of the past. In addition, your pulse coil can build up higher voltages, which has a positive effect on the upper speed limit of heavily tuned motors.
Advantages of the electronic ignition module:
- No wear
- Maintenance-free
- Higher voltage in the upper engine speed range
- Higher engine speeds possible than with conventional contact ignition
- Maintenance-free;
- Easy way to install a cut-off switch or kill switch
Mounting on ignitions with internal ignition coil:
- Mount the box close to the motor, e.g.B. on the motor screw
- Remove the capacitor from your contact ignition
- Remove the ignition coil cable from the capacitor, as well as the cable leading outwards inside your ignition;
- connect the cable of the interrupter with a new cable and lead this to the outside to the first connection of the module
- attach a new cable to the small cable of the ignition coil (e.g. the cable of the ignition coil).B. listed in the accessories) and route this to the outside to the middle connection of the module
- connect the right-hand connection to a ground point on the frame, e.g. on the motor screw
Installation for ignition systems with external ignition coil:
- Mount the box close to the external ignition coil, e.g. on the motor screw
- remove the capacitor from your contact ignition
- remove the cable of the pulse coil and the cable leading outwards inside your ignition from the breaker
- connect the breaker with a new cable and lead this outwards to the first connection of the module
- attach a new cable to the pulse coil (e.g. as described in the accessories manual).
- attach a new cable to the pulse coil (as listed in the accessories, for example) and route this outwards to the middle connection of the module
- Also attach the cable that leads to the external ignition coil to the middle connection of the module
- connect the right-hand connection of the module to a ground point on the frame, e.g. on the motor screw
- .e.g. on the motor screw
Notes: The breaker spacing can be left at 0.4-0.5 mm. Pay attention to the cable routing inside the ignition so that it is not damaged by the rotating flywheel. Your light coil supplies 6 V as before, so there is no need to convert your bulbs to 12 V. There is no need to flash off or adjust the preamplification.
You can find more parts for your ignition system on your Puch moped in the accessories section.
Quality product from the Italian manufacturer SparkEVO.
The set includes the following fixed parts:
Manufacturer: SparkEVO · Height: 33.5 mm, 15.3 mm · Mounting type: Tab for screwing · Connection type: Plug connection · Ø mounting hole: 5.3 mm · Area of application: Tuning
Details
| Manufacturer | SparkEVO |
| Ø mounting hole | 5.3 mm |
| Area of application | Tuning |
| Mounting type | Tab for screwing |
| Connection type | Plug connection, Tab for screwing |
| Height | 33.5 mm, 15.3 mm |
Suitable for the following models
| Puch |
Accessories & related products
Luster terminal 3-pole black small (0.1 - 2.5 mm²)
Cable cross-section: 0.1 - 2.5 mm · Number of connections: 6 pcs · Manufacturer: Made in Germany · Material: Brass · Material: Plastic · Material: Steel · Color: black · Total length: 18.5 mm · Width: 22 mm · Clamping diameter: 3.3 mm · Number of components: 1 pcs · Height: 15.5 mm · Area of application: Workshop accessories
1,55 EUR
Hot 
Leonelli 6V voltage regulator (1A quality)
Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Tension: 6 V · Surface: raw · Performance: 50 W · Type of current: Alternating current (AC) · Total length: 50 mm · Width: 27 mm · Height: 15 mm · Mounting type: Screws · Ø mounting hole: 6 mm
33,40 EUR
HPI racing ignition 12V with light 60W
Manufacturer: HPI · Material: Aluminum · Material: Steel · Ø cable: 7 mm · Light coil voltage: 12 V · Tension: 12 V · Performance: 60 W · Direction of rotation: left · Direction of rotation: right · Ø mounting plate: 90 mm · Ø Internal flywheel: 61.5 mm · Mounting type: Screws · Ø Flywheel outside: 71.5 mm · Number of fixing points: 6 pcs · Area of application: Tuning · Weight: 340 g
335,20 EUR
swiing® revival cable repair set ignition
Ø single core: 0.15 mm · Manufacturer: swiing® revival parts · Material: Copper · Material: Plastic · Area of application: Standard · Number of cables: 2 pcs · Surface: raw · Cable cross-section [mm²]: 0.75 mm² · Cable cross-section [mm²]: 1 mm² · Color: black · Color: yellow · Ø outside: 1.9 mm · Total length: 300 mm
9,95 EUR
BOSCH Breaker without cable reinforced | Bosch / Ducati
Manufacturer: BOSCH · Material: Steel · Area of application: Tuning · Cable available: No · Ø axle: 4 mm · Number of fixing points: 1 pcs · Ø mounting hole: 4.5 mm · Ø Internal flywheel: 90 mm · Alternative version of the Pony Spare part no.: A4606 · BOSCH spare part no.: 1 217 013 020 · Alternative version of Sachs spare part no.: 0983 106 000 · BERU spare part no.: 0 340 100 466
23,40 EUR
Hot
VEC electronic ignition coil (replaces ignition coil, capacitor & contact breaker)
Manufacturer: VEC · Area of application: Original · Area of application: Performance · Area of application: Standard · Color: black · Ø cable holder: 5 mm · Place of use: Internal (in the ignition) · Total length: 77 mm · Height: 48 mm · Number of fixing points: 2 pcs · Ø mounting hole: 4.6 mm · Mounting type: Screws · Hole spacing: 54 mm · Cable length: 140 mm · Cable length: 420 mm · Ø Internal flywheel: 90 mm
111,70 EUR
Not in stock
Moped fans like you also bought:
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Color: silver · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Ø cable: 5 mm · Ø cable: 7 mm · Pony spare part no.: A2099 · Sachs spare part no.: 0265 100 00
9,75 EUR
swiing® revival rubber grommet ignition | Puch X30 Z50
Manufacturer: swiing® revival parts · Area of application: Standard · Material: Rubber · Color: black · Surface: raw · Total length: 19.3 mm · Ø Cable bushing: 2.5 mm · Ø Cable bushing: 5.2 mm · Width: 15.6 mm · Height: 3.5 mm · Total height: 11.3 mm
8,85 EUR
Gas cable Ø 1.25 mm x 220 cm (cylindrical nipple) Bing
Ø nipple: 3 mm · Nipple length: 5 mm · Manufacturer: Made in Germany · Area of application: Standard · Material: Steel · Surface: blue galvanized · Ø Stranded wire: 1.25 mm · Nipple shape: Cylinder · Cable length: 2200 mm · Number of components: 1 pcs
3,15 EUR
Fortune / Merrick 2.00-2.50 x 16/17" inner tube
Manufacturer: Fortune · Tire width [inch]: 2 - 2.5 " · Tire width [mm]: 50.8 - 63.5 · Width [inch]: 2 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Old designation: 20 x 2 · Old designation: 20 x 2.25 · Old designation: 20 x 2.5 · Old designation: 21 x 2 · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Tire height [%]: 100 · Valve type: TR4 Auto valve · Wheel size [inch]: 16 - 17 " · Wheel size [inch]: 17 "
11,10 EUR
Continental 2.25 x 17" KKS
Manufacturer: Continental · Tire width [inch]: 2.25 " · Color: black · Tire width [mm]: 57.15 · Old designation: 21 x 2.25 · Speed index: B = 50 km/h · Load capacity index: 39 = 136 kg · Profile type: KKS 10 · Tire type: Allround · White wall: No · Wheel size [inch]: 17 " · Tubeless (yes/no): Tubetype TT (requires hose)
62,50 EUR
Collection only possible with online purchase and appointment.
