Stage6 adapter intake manifold Mikuni carburetor 24 mm

4-piece sealing paper set

Place of use: Universal · Manufacturer: Made in Spain · Thickness: 0.25 mm · Thickness: 0.4 mm · Thickness: 0.5 mm · Thickness: 1.2 mm · Material: Sealing carton · Material: Sealing paper

24 mm flat slide carburetor MIKUNI Handchoke

Carburetor type: Flat slide valve · Nominal diameter: 24 mm · Height: 130 mm · Ø Air filter connection: 44 mm · Ø fuel hose connection: 6 mm · Choke control: Hand choke · Nozzle thread: M5.3x0.9 (standard thread) · Nozzle size: 130 · Size of secondary nozzle: 51 · Mounting type: Plug connection · Width: 75 mm · Area of application: Tuning

Athena Athesil sealing compound gray (silicone) 80 ml permanently elastic up to 300 °C

Manufacturer: Athena · Material: Silicone · Area of application: Chemistry · Color: gray · Contents [ml]: 80 ml · Temperature resistance (min.): -40 - 300 °C

Stage6 reed valve block VForce 3 by Moto Tassinari

Manufacturer: Stage6 · Number of flaps: 8 pcs · Hole spacing: 52 mm

Stage6 adapter intake manifold Dell'Orto / Polini CP carburetor 21 mm

Manufacturer: Stage6 · Material: Rubber · Ø inside: 21 mm · Hole spacing inlet: 60 mm

Stage6 adapter intake manifold PWK carburetor 19 - 28 mm

Manufacturer: Stage6 · Material: Rubber · Ø inside: 30 mm · Ø inside: 33 mm · Hole spacing inlet: 60 mm

Stage6 adapter intake manifold PWK carburetor from 30 mm

Manufacturer: Stage6 · Material: Rubber · Ø inside: 35 mm · Ø inside: 40 mm · Hole spacing inlet: 60 mm

Heat protection tape with fastening blue 5 m

Material: Chrome steel (stainless steel) · Material: Fiber · Total length: 5000 mm · Color: blue · Width: 50 mm · Thickness: 1.5 mm

ADDY GME engine housing "der.pruefstand" Edition | Puch E50

Manufacturer: ADDY · Material: Aluminum

ADDY GME engine housing spindled "der.pruefstand" Edition | Puch E50

Manufacturer: ADDY · Material: Aluminum

Intake manifold 25 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Manufacturer: Made in Switzerland · Material: Chrome steel (stainless steel) · Ø inside: 25 mm · Hole pattern [mm]: 55 / 60

Intake manifold 29 mm ADDY GME engine housing "der.pruefstand" Inox | Puch E50

Manufacturer: Made in Switzerland · Material: Chrome steel (stainless steel) · Ø inside: 29 mm · Hole pattern [mm]: 55 / 60

HK Clutch "Racing" Kickstarter | Puch E50

Manufacturer: HK Clutches · Area of application: Racing · Material: Steel · Material addition: Aluminum · Number of jaws: 3 pcs · Thickness: 20.3 mm · Recording type: Cone mounting · Ø inside: 13.6 mm · Ø inside: 14.6 mm · Number of springs: 3 pcs · Ø outside: 93 mm

Stage6 R/T RT-PWK 24 mm carburetor Stage6 *Black Edition*

Manufacturer: Stage6 R/T · Surface: varnished · Carburetor type: RT-PWK · Color: black · Nominal diameter: 24 mm · Ø Air filter connection: 50 mm · Mixed oil connection: Yes · Vacuum connection: Yes · Choke control: Hand choke · Nozzle thread: M5x0.8 (standard thread) · Mounting type: Flange · Mounting type: Plug connection · Area of application: Tuning

MBR clutch basket 18 teeth Racing straight short | Puch E50

Manufacturer: MBR · Toothing type: helical toothed · Number of teeth: 18 pcs · Area of application: Tuning

MBR spur gear 94 teeth "Racing" straight | Puch E50

Manufacturer: MBR · Material: Steel · Surface: hardened & ground · Recording type: Interlocking · Toothing type: straight toothed · Number of teeth: 94 pcs · Ø axle: 17 mm · Ø outside: 145 mm

MBR clutch basket & spur gear 18:94 teeth Racing straight short | Puch E50

Manufacturer: MBR · Toothing type: straight toothed · Number of teeth: 18 pcs · Number of teeth: 94 pcs · Area of application: Tuning

swiing® ingenious crankshaft High End with mounted bearings (Version 2.0) | Puch E50

Manufacturer: swiing® ingenious parts · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 43 mm · Connecting rod length center-center: 90 mm · Total length of crankpin on clutch side: 74 mm · Total length crankpin ignition side: 66 mm · Ø crank webs: 69.9 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 17 mm · Ø Bearing seat (ignition side): 17 mm · Thread type: MF10x1 (fine pitch thread) · Thread length: 11 mm · Thread length: 15 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 34 mm · Length 1st paragraph: 9 mm · Length 2nd paragraph: 14.5 mm · Length 3rd paragraph: 25 mm · Ø 1st step (on the coupling side): 22 mm · Ø 2nd shoulder (on the clutch side): 17 mm · Ø 3rd step (on the clutch side): 15 mm · Length of shoulder (ignition side): 26.3 mm · Weight: 968 g · Number of gears: 1 pcs · Area of application: High End · Area of application: Racing · Area of application: Tuning

swiing® ingenious pull starter Selettra ignition | Puch E50

Manufacturer: swiing® ingenious parts · Material: Plastic · Material: Steel · Surface: chrome-plated · Color: Chrome · Ignition system: Selettra · Number of fixing points: 2 pcs

Selettra rotor P3356 for NO2019 analog & A11

Manufacturer: Selettra · Direction of rotation: left · Direction of rotation: right · Weight: 352 g · Cone ratio: 1:5 · Ø Flywheel outside: 58 mm

Selettra stator for A11 analog

Manufacturer: Selettra · Area of application: Tuning · Surface: coated · Color: black · Color: red · Number of cables: 2 pcs · Number of fixing points: 3 pcs

Selettra ignition coil A11 analog Superseal plug

Manufacturer: Selettra · Place of use: Universal · Color: black · Color: red · Mounting type: Stud bolts & nuts · Number of fixing points: 2 pcs