Reinforced pull pin suitable for the manual Z50 engine of Puch X30 Sport NS / NL, as well as Puch X30 Velux mopeds / mopeds.
Execution with axial bearing: The pure axial bearing is designed for extreme loads with very strong clutch springs.
Due to the slightly poorer guidance, however, this bearing can make a little more noise than conventional bearings with a 60° contact angle.
The reinforced clutch springs in the accessories can be used in conjunction with the clutch bearing without any problems.
Adjusting the clutch: Figure 4 shows the position of the clutch release lever in relation to the abutment and the ball collar nut in relation to the clutch release shaft. This setting results in maximum disengagement with minimum effort. Particular attention must be paid to the play between the decoupling shaft and the conical collar nut, as the clutch bearing will inevitably break within a very short time if the play is too small. With the clutch cable engaged, the free travel on the clutch release lever should be approx. 3 mm.
The angle «A» on the picture is 58°. On the hand lever, these clearances result in an empty travel of approx. 1 cm.
Good, inexpensive standard spare part. GPO – GOOD PARTS ONLY.
Details
Manufacturer | GPO |
Material | Metal |
Area of application | Tuning |
Suitable for the following models
Puch | Z50 (X30 Sport) Z50 (X30 Velux) 2-Gang MS, MV, MV50 |
Accessories & related products
swiing® revival clutch spring 2-disc version (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4 mm · Manufacturer: swiing® revival parts · Ø inside: 30.5 mm · Number of components: 1 pcs · Material: Spring steel · Surface: raw · Color: gray · Ø outside: 39 mm · Area of application: Original · Area of application: Standard · Total length: 19.5 mm
20,00 EUR
swiing® ingenious clutch spring reinforced +20% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø inside: 30 mm · Ø wire: 4.6 mm · Manufacturer: swiing® ingenious parts · Area of application: Tuning · Material: Spring steel · Color: blue · Surface: coated · Total length: 20.5 mm · Ø outside: 39 mm · Number of components: 1 pcs
26,60 EUR
swiing® ingenious clutch spring reinforced +40% (Version 2.0) | Puch Z50
Spring design: Pressure spring · Ø wire: 4.5 mm · Manufacturer: swiing® ingenious parts · Ø inside: 30 mm · Number of components: 1 pcs · Material: Spring steel · Surface: coated · Color: red · Ø outside: 39 mm · Area of application: Tuning · Total length: 23.5 mm
26,60 EUR
Moped fans like you also bought:
swiing® revival gasket set Z50 engine | Puch X30 NS / NL
Manufacturer: swiing® revival parts · Area of application: Standard · Material: Sealing paper · Ø outlet inside: 22 mm · Hole spacing inlet: 32 - 38 mm · Number of components: 10 pcs · Hole pattern [mm]: 44 x 44 · Hole spacing outlet: 42 mm
22,20 EUR
Not in stock
Magura gas cable clamp / deco cable clamp Ø 5 x 6 mm
Ø Cable bushing: 1.6 mm · Manufacturer: Magura · Number of components: 2 pcs · Material: Brass · Material: Steel · Surface: nickel-plated · Thread type: M4x0.7 (standard thread) · Ø outside: 5 mm · Drive: Slot · Screw head: Lens head · Thread length: 4 mm · Total length: 6 mm
2,25 EUR
Motorex engine oil (gear oil) manual 450 ml
Manufacturer: Motorex · Temperature resistance (min.): -30 - 220 °C · Viscosity (SAE): 80W · Oil type: GL4 · Contents [ml]: 450 ml · Gearbox type: Foot control · Gearbox type: Manual gearshift · Area of application: Gearbox lubrication with clutch
11,10 EUR
24,67 EUR/l
swiing® revival wiring harness MERIT light switch (version 2.0)
Cable cross-section [mm²]: 1.5 mm² · Manufacturer: swiing® revival parts · Switch included: Yes · Number of cables: 5 pcs · Area of application: Standard · Cable bifurcation to motor: 950 mm · Luster terminal: Yes · Cable bifurcation to lamp: 230 mm · Ø Receptacle: 22 mm · Cable bifurcation to switch: 400 mm · Tail light cable length: 1000 mm
44,60 EUR