The Spark EVO Zero Basic module (version 2.0) was developed to make the breaker ignition on your Piaggio Ciao, Si, Bravo, Boxer moped / moped significantly more wear-resistant and low-maintenance.
The box only uses the breaker as a clock generator and replaces the capacitor at the same time. Problems with worn breaker contacts and poor quality capacitors are therefore a thing of the past. In addition, your pulse coil can build up higher voltages, which has a positive effect on the upper speed limit of heavily tuned motors.
Advantages of the electronic ignition module:
- No wear
- Maintenance-free
- Higher voltage in the upper speed range
- Higher speeds possible than with conventional contact ignition
- Easy way to install a cut-off switch or kill switch
Mounting:
- Mount the box close to the external ignition coil, e.g. on the motor screw .e.g. on the motor screw
- Remove the capacitor from your contact ignition
- Remove the pulse coil cable and the cable leading to the outside inside your ignition from the breaker
- Connect the breaker with a new cable and lead this to the outside. This is connected to the left contact of the module.
- attach a new cable to the pulse coil (such as
- attach a new cable to the pulse coil (as listed in the accessories) and run this to the outside to the middle connection of the module
- Also attach the cable that runs to the external ignition coil to the middle connection of the module
- connect the right-hand connection to a ground point on the frame, e.g. to the motor screw
- .e.g. on the motor screw
Notes: The breaker gap remains at 0.4 - 0.5 mm. Pay attention to the cable routing within the ignition so that they are not damaged by the rotating flywheel.
Your light coil supplies 6 V as before, so there is no need to convert your bulbs to 12 V.
Other parts for your Piaggio ignition system can be found in the accessories section.
Quality product from the Italian manufacturer SparkEVO.
Details
| Manufacturer | SparkEVO |
| Height | 33.5 mm, 15.3 mm |
| Mounting type | Tab for screwing |
| Connection type | Plug connection, Tab for screwing |
| Ø mounting hole | 5.3 mm |
| Area of application | Tuning |
Suitable for the following models
| Piaggio | Ciao - Ciao, Ciao, Ciao, Ciao Si Bravo/Superbravo Boxer Grillo |
Accessories & related products
Luster terminal 3-pole black small (0.1 - 2.5 mm²)
Cable cross-section: 0.1 - 2.5 mm · Number of connections: 6 pcs · Manufacturer: Made in Germany · Material: Brass · Material: Plastic · Material: Steel · Area of application: Workshop accessories · Total length: 18.5 mm · Color: black · Width: 22 mm · Height: 15.5 mm · Clamping diameter: 3.3 mm · Number of components: 1 pcs
1,65 EUR
Hot 
Leonelli 6V voltage regulator (1A quality)
Manufacturer: Leonelli · Material: Aluminum · Material: Plastic · Surface: raw · Tension: 6 V · Mounting type: Screws · Type of current: Alternating current (AC) · Performance: 50 W · Total length: 50 mm · Height: 15 mm · Width: 27 mm · Ø mounting hole: 6 mm
34,80 EUR
swiing® revival cable repair set ignition
Cable cross-section [mm²]: 0.75 mm² · Cable cross-section [mm²]: 1 mm² · Ø single core: 0.15 mm · Manufacturer: swiing® revival parts · Material: Copper · Material: Plastic · Surface: raw · Color: black · Color: yellow · Total length: 300 mm · Number of cables: 2 pcs · Area of application: Standard · Ø outside: 1.9 mm
10,30 EUR
GPO breaker without cable (version 2.0) | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Material: Steel · Cable available: No · Ø axle: 5 mm · Number of fixing points: 1 pcs · Ø mounting hole: 5 mm · Area of application: Original · Area of application: Standard · Piaggio OEM number: 103133
11,50 EUR
HPI racing ignition 12V with light breaker housing | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: HPI · Light coil voltage: 12 V · Performance: 60 W · Direction of rotation: right · Ø mounting plate: 90 mm · Ø Internal flywheel: 61.5 mm · Ø Flywheel outside: 140 mm · Ø cable: 7 mm · Mounting type: Screws · Number of fixing points: 4 pcs · Area of application: Tuning
406,70 EUR
GPO Electronic ignition 12V | Piaggio Ciao, SI, Bravo, Boxer
Manufacturer: GPO · Light coil voltage: 12 V · Performance: 90 W · Direction of rotation: right · Mounting type: Screws · Number of fixing points: 3 pcs · Area of application: Original · Area of application: Standard · Piaggio OEM number: 181103 · Piaggio OEM number: 219965 · Piaggio OEM number: 244127
267,20 EUR
Moped fans like you also bought:
BERU spark plug connector / 1 kΩ interference suppressed
Manufacturer: BERU · Material: Sheet metal (steel) · Spark plug socket: M4 · Cable available: No · Suppressed: Yes · Resistance: 1000 Ω · Ø cable: 5 mm · Ø cable: 7 mm · Color: silver · Pony OEM number: A2099 · Sachs OEM number: 0265 100 00
10,20 EUR
Michelin 2.25 - 2.50 x 17" tube
Manufacturer: Michelin · Tire width [inch]: 2.25 - 2.5 " · Tire width [mm]: 57.15 - 63.5 · Width [inch]: 2 1/4 · Width [inch]: 2 1/2 · Tire height [%]: 100 · Wheel size [inch]: 17 " · Old designation: 21 x 2.25 · Old designation: 21 x 2.5 · Valve type: TR4 Auto valve
17,30 EUR
Collection only possible with online purchase and appointment.
