Hot 
The legendary high-end crankshaft suitable for Sachs 50 (without blower) and 50/3 engines.
The shaft can also be used in the 50/2 (also called 502) and 503 engines with minor adjustments.
High-quality and precisely fitting full-flange crankshaft with polished connecting rod, which has proven itself in various load tests. Designed for use in engines with a large power increase and tested up to 19,000 rpm.
The crankshaft can also be used on Sachs 503 engines, so that the drive wheel does not rub against the housing, it must be shimmed with 1.5 mm spacers. The matching spacers can be found in the accessories section.
The large balancing holes in the cheeks have been sealed with aluminum inserts for maximum pre-compression.
This crankshaft is designed for E15 main bearings.
Dimensions of the crankshaft:
- Total length of clutch-side crankpin: 41.5 mm
- Total length of clutch-side crankpin: 63.7 mm
- Length 1st shoulder (clutch-side): 18.5 mm
- Length 2nd shoulder (clutch side) 14 mm
- Ø 1st shoulder (clutch side): 15 mm
- Ø 2nd heel (coupling side): 12 mm
- Thread (coupling side): MF10x1 mm
- Length of shoulder (on coupling side): 37 mm
- Ø shoulder (on end face): 15 mm
- Thread (on end face): MF10x1 mm
- Ø crank webs: 84.9 mm
- Width of crank webs: 29.8 mm
- Ø Connecting rod eye top: 16 mm
- Ø Connecting rod pin bottom: 16 mm
- Cleuellänge (center-center): 84 mm
- Stroke: 42 mm
- Weight (incl. connecting rod): 1026 grams
- Dimension needle bearing: Ø 12 / 16 x 15.7 mm (axe 12)
Attention: The width of the needle bearing is 15.2 mm, depending on the piston it may need to be slightly recessed inside.
Installation tip: The transition between the crank webs and the crankpin is provided with a slight radius for reinforcement. In order to be able to distance out cleanly, a 16 x 1 mm spacer washer should be used on the left and right, which lays cleanly over the chamfer and is therefore also perfectly centered. The other spacers can be used normally with Ø 15 mm.
Quality product from the Portuguese manufacturer Rito.
Details
| Manufacturer | Rito |
| Material | Steel, Aluminum |
| Cheek type | Full cheeks |
| Crankshaft stroke | 42 mm |
| Thread type | MF10x1 (fine pitch thread) |
| Connecting rod length center-center | 84 mm |
| Total length of crankpin on clutch side | 41.5 mm |
| Total length crankpin ignition side | 63.7 mm |
| Ø crank webs | 84.9 mm |
| Ø piston pin (B) | 12 mm |
| Ø Connecting rod eye | 16 mm |
| Weight | 1026 g |
| Ø Bearing seat (clutch side) | 15 mm |
| Area of application | High End, Racing, Tuning |
| Ø Bearing seat (ignition side) | 15 mm |
| Thread length | 7 mm, 9 mm |
| Dimension needle bearing | 12 / 16 x 15.7 mm (axe 12) |
| Wide crank webs | 29.8 mm |
| Length 1st paragraph | 18.5 mm |
| Length 2nd paragraph | 14 mm |
| Ø 1st step (on the coupling side) | 15 mm |
| Ø 2nd shoulder (on the clutch side) | 12 mm |
| Length of shoulder (ignition side) | 37 mm |
| Number of gears | 2 pcs |
Suitable for the following models
| Sachs | 50 (Fahrtwind, 1.25 / 1.5 PS, DE) 50/2 - L CH (0.8 PS), ML CH (0.8 PS), MB (2.6 PS), MLB (2.6 PS) 50/3 |
Accessories & related products
swiing® ingenious puller L17 / BO15 / E15 shoulder bearing
Width across flats (trigger): 8 mm · Width across flats (trigger): 19 mm · Span: 24 mm · Manufacturer: swiing® ingenious parts · Clamping depth: 10 mm · Peel-off tray: BO15 · Peel-off tray: E15 · Peel-off tray: L17 · Area of application: (Dis)assembly tool · Surface: galvanized (blue) · Diameter: 24 mm · Diameter: 40.3 mm · Number of components: 1 pcs · Thread type: M6x1 (standard thread) · Thread type: M8x1.25 (standard thread) · Total length: 120 mm
49,10 EUR
Not in stock
NSK E15 shoulder ball bearing 15/35/8 (A1149)
Stock number: E15 · Inner ring width: 8 mm · Manufacturer: NSK · Bearing clearance: CN (standard) · Bearing cage: Brass cage ball-guided · Groove ring: No · Material: Brass · Area of application: Standard · Material: Steel · Surface: blank · Bearing type: Shoulder bearing · Width: 8 mm · Ø inside: 15 mm · Ø outside: 35 mm · Ball bearing closed: No · Pony spare part no.: A1149 · Sachs spare part no.: 0232 017 006
27,80 EUR
swiing® revival shim set | Sachs 503, 502, 50/2, 50/3
Nominal diameter inside: 13 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Ø inside: 12.5 mm · Ø inside: 15.2 mm · Ø outside: 18 mm · Ø outside: 21 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.4 mm · Thickness: 0.45 mm · Thickness: 0.5 mm · Thickness: 1 mm
18,90 EUR
swiing crankshaft High End (Version 2.0) | Sachs 503 2AL, 2BL
Manufacturer: swiing · Material: Aluminum · Material: Steel · Cheek type: Full cheeks · Crankshaft stroke: 42 mm · Connecting rod length center-center: 85 mm · Total length of crankpin on clutch side: 43.5 mm · Total length crankpin ignition side: 63.4 mm · Ø crank webs: 85 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 15 mm · Ø Bearing seat (ignition side): 15 mm · Thread type: MF10x1 (fine pitch thread) · Thread length: 8 mm · Thread length: 11 mm · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 30.1 mm · Length 1st paragraph: 21 mm · Length 2nd paragraph: 13 mm · Ø 1st step (on the coupling side): 15 mm · Ø 2nd shoulder (on the clutch side): 12 mm · Length of shoulder (ignition side): 35 mm · Number of gears: 2 pcs · Area of application: High End · Area of application: Racing · Area of application: Tuning
210,00 EUR
Not in stock
Hot
swiing crankshaft High End (Version 2.0) | Sachs 50/2, 50/3
Manufacturer: swiing · Cheek type: Full cheeks · Crankshaft stroke: 42 mm · Connecting rod length center-center: 85 mm · Total length of crankpin on clutch side: 40.7 mm · Total length crankpin ignition side: 63.4 mm · Ø crank webs: 85 mm · Ø piston pin (B): 12 mm · Ø Connecting rod eye: 15 mm · Ø Bearing seat (clutch side): 15 mm · Ø Bearing seat (ignition side): 15 mm · Thread type: MF10x1 (fine pitch thread) · Dimension needle bearing: 12 / 15 x 14.2 mm (axe 12) · Wide crank webs: 30.1 mm · Weight: 1038 g · Area of application: High End
210,00 EUR
Not in stock
Moped fans like you also bought:
Oil seal NBR 15/30/7 B AS | Sachs 503, 50/2
Simmering type: B - With sheet metal outer casing / one sealing lip. · Ø inside: 15 mm · Ø outside: 30 mm · Manufacturer: Sachs · Material: NBR · Width: 7 mm · Temperature resistance (min.): -30 - 100 °C · Pony spare part no.: A1830 · Sachs spare part no.: 0250 090 000
6,05 EUR
NSK E15 shoulder ball bearing 15/35/8 (A1149)
Stock number: E15 · Inner ring width: 8 mm · Manufacturer: NSK · Bearing clearance: CN (standard) · Bearing cage: Brass cage ball-guided · Groove ring: No · Material: Brass · Area of application: Standard · Material: Steel · Surface: blank · Bearing type: Shoulder bearing · Width: 8 mm · Ø inside: 15 mm · Ø outside: 35 mm · Ball bearing closed: No · Pony spare part no.: A1149 · Sachs spare part no.: 0232 017 006
27,80 EUR
swiing® revival gearbox cover gasket | Sachs 503 AAL, ABL, AB, AC, ADV, 2AL, 2BL (A1888)
Color: sand-colored · Manufacturer: swiing® revival parts · Number of components: 1 pcs · Material: Sealing paper · Width: 130 mm · Thickness: 0.35 mm · Total length: 200 mm · Number of fixing points: 6 pcs · Pony spare part no.: A1888 · Sachs spare part no.: 0250 150 000
6,05 EUR
swiing® revival shim set | Sachs 503, 502, 50/2, 50/3
Nominal diameter inside: 13 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: blank / oiled · Ø inside: 12.5 mm · Ø inside: 15.2 mm · Ø outside: 18 mm · Ø outside: 21 mm · Thickness: 0.1 mm · Thickness: 0.15 mm · Thickness: 0.2 mm · Thickness: 0.4 mm · Thickness: 0.45 mm · Thickness: 0.5 mm · Thickness: 1 mm
18,90 EUR
swiing® revival engine seal | Sachs 502, 50/2, 50/3, 50/4 (A1828)
Number of components: 1 pcs · Manufacturer: swiing® revival parts · Material: Sealing paper · Color: sand-colored · Total length: 250 mm · Width: 170 mm · Thickness: 0.4 mm · Ø inside: 86 mm · Number of fixing points: 16 pcs · Pony spare part no.: A1828 · Sachs spare part no.: 0250 088 100
6,60 EUR
Oil seal FPM 15/30/7 B DUO VITON | Sachs 50/2, 503
Temperature resistance (min.): -30 - 200 °C · Simmering type: B DUO - With sheet metal outer casing / two sealing lips. · Ø inside: 15 mm · Width: 7 mm · Manufacturer: Sachs · Material: FPM - Rubber · Surface: raw · Ø outside: 30.1 mm · Area of application: Standard · Pony spare part no.: A1830 · Sachs spare part no.: 0250 090 000
8,85 EUR
GPO piston 40.94 mm | Sachs 502, 50/2, 50/3, 50/4
Manufacturer: GPO · Thick piston ring: 1.8 mm · Ø outside piston (A): 40.94 mm · Compression height (C): 28 mm · Curvature (D): 3.2 mm · Total piston height (E): 49.4 mm · Number of piston rings (F): 2 pcs · Nominal diameter: 40 mm · Piston ring mold: Rectangular ring · Piston ring impact: Internal fuse (IS) · Ø piston pin (B): 12 mm · Piston ring height: 1.5 mm · Piston weight: 86 g
44,60 EUR
Collection only possible with online purchase and appointment.
